Sign Up Now
FREE E-Newsletter

Search


About Us

ABOUT SSL CERTIFICATES
Home > Vibration Switches > Electronic Switches > 685B0001A30
 

 

Electronic Vibration Switch
Model 685B0001A30     
 
Electronic vibration switch, internal ICP®, 0-1.5 ips, AC powered, 10A form C relays, BNC acceleration output, dual cord grips

685B series electronic vibration switch with internal sensor, 0-1.5 ips scale factor, 85-245 Vac power, 5A from C relays (SPDT), external BNC connection for raw vibration output, and dual 1/2" NPT conduit hubs.

  • Measurement Range: 0 to 1.5 in/sec pk (0 to 38.1 mm/s pk)
  • Enclosure: Internal and Remote Reset
  • Cable Input: Dual Cord Grips
  • Relay: (Alert) 10 A, 245 VAC/30 VDC, Form C
  • Relay: (Alarm) 10 A, 245 VAC/30 VDC, Form C
  • Power Required: 85-245 VAC 50/60 Hz
 
 
SpecificationsDrawingProduct ManualPictureDownloads 
PERFORMANCE ENGLISH SI
Measurement Range 0 to 1.5 in/sec pk
0 to 38.1 mm/s pk
Frequency Range (±3 dB) 120 to 60,000 cpm
2 to 1,000 Hz [6]
Power On Delay 20 sec
20 sec [3]
Relay (Alert) 10 A, 245 VAC/30 VDC, Form C
10 A, 245 VAC/30 VDC, Form C
Relay (Alarm) 10 A, 245 VAC/30 VDC, Form C
10 A, 245 VAC/30 VDC, Form C
Relay Latching / Non-Latching
Latching / Non-Latching
Relay Normally Open / Closed
Normally Open / Closed
Alarm Setpoint 10 to 100% of Vibration Range
10 to 100% of Vibration Range
Alert Setpoint 10 to 100% of Alarm Setpoint
10 to 100% of Alarm Setpoint
Delay (Alert) 0 to 45 sec
0 to 45 sec
Delay (Alarm) 0 to 45 sec
0 to 45 sec
Acceleration Output (±10 %) 100 mV/g
10.2 mV/(m/s2)
CONTROL INTERFACE
Power LED Green
Green
Alarm LED Red
Red
Alert LED Yellow
Yellow
Time Delay Adjustment Single Turn Potentiometer
Single Turn Potentiometer
Reset Function Momentary Pushbutton Switch
Momentary Pushbutton Switch [4]
Self Test Function Momentary Pushbutton Switch
Momentary Pushbutton Switch
ENVIRONMENTAL
Temperature Range (Operating) -22 to 158 °F
-30 to 70 °C
Temperature Range (Storage) -40 to 257 °F
-40 to 125 °C
Enclosure Rating Nema 4X
IP66
ELECTRICAL
Power Required 85-245 VAC 50/60 Hz
85-245 VAC 50/60 Hz
Current Consumption <150 mA
<150 mA
Output Current 4 to 20 mA
4 to 20 mA [2]
External Calibration Input 4 to 20 mA
4 to 20 mA [1]
PHYSICAL
Size - Width 3.5 in
90 mm
Size - Height 2.8 in
70 mm
Size - Depth 3.5 in
90 mm
Weight 1.85 lb
839 gm
Mounting Torque (Cover Screw) 4.1 ft-lb
5.7 N-m
Mounting Torque (Base) 2 to 5 ft-lb
3 to 7 N-m
Sensing Element (Internal) 100 mV/g ICP" Accelerometer
100 mV/g ICP" Accelerometer
Housing Material Aluminum Alloy
Aluminum Alloy
Electrical Connector Screw Terminals
Screw Terminals
Enclosure Internal and Remote Reset
Internal and Remote Reset
Enclosure Buffered Acceleration Signal through External BNC (100 mV/g)
Buffered Acceleration Signal through External BNC (100 mV/g)
Screw Terminal Wire Size 24-14 AWG
0.2 - 2.5 mm2
Cable Input Dual Cord Grips
Dual Cord Grips
Mounting Hole Size 0.21 in
5.4 mm

All specifications are at room temperature unless otherwise specified.
NOTES:
[1] Active only during calibration mode
[2] Current will fluctuate at frequencies below 5 Hz.
[3] Factory Set
[4] Reset can also be engaged via external connection to common
[5] See PCB Declaration of Conformance PS051 for details.
[6] To obtain 60000 cpm (1000 Hz) frequency response, grease must be applied to all mechanical couplings. Otherwise, frequency response is limited to approximately 30000 cpm (500 Hz)




View Spec Sheet: 685B0001A30_H.pdf